![]() If you are among those without this light attached to your bezel, you will need to order one from Ford. *Additional parts are needed to complete this install and are not included.Ĭenter console, shifter assembly middle ac vents/dash trim etc.īe aware that your bezel may not have the oem ambient light attached to it. An awesome upgrade to any column shifter equipped truck, including standar/regular cab trucks! If your truck isnt set up the way you want it, you dont need a new truck….you need to be more fanatical and build it the way you want it to be! All PnP with no wires to cut, and no soldering….just a professional oem looking and functioning harness built by fanatics! All wires are proper automotive grade, not basic hook up wires, and all terminals are crimped using professional tooling from Molex & TE Connectivity, providing accurate and full crimping of the wire and the jacket around the wire. Some of the items we sell include bench seat upgrades, organizer trays and kits, phone grips, as well as security console inserts. In addition to performing the conversion from column shifter the center console shifter, our harness also provide oem backlighting of the shifter bezel. My mounts include some offset holes for Corbeau seats on most brackets but other brands will be centered on the bracket.Our Series 1 column shifter to center console shifter conversion harness will allow you to easily get rid of the column mounted shifter assembly that your truck came with, and upgrade your truck to the sportier look, feel, and function of the center console shifter. With aftermarket seats that fit more snuggly this will be more obvious, but it is not an issue. This is not obvious while driving or unless you are looking for it with stock seats. Note: Just about every car or truck made in the last 30 years has the steering wheel and seat slightly offset. After this, the next thing to do is to have all holes in the locked vault lined up with threaded holes at the console’s bottom. Now open the locked vault, then gently place it in the empty console. Genuine GM Console Microphone Hummer H2 Cadillac CTS DTS STS New OEM 15246939. You can now remove the 10mm nuts from the console with these. Hummer H2 Silverado Escalade Tahoe Yukon Seat Track Cover Cap Black 15214533. There is an extra charge for custom siding and additional wait time (usually 2-3 weeks) due to having them designed and cut. To do this, you need two tools: a ratchet and a 10mm socket. The outside face is available with the AFP logo with slots on either side, the LSX logo, or a Custom siding which can be whatever you want. The brackets can be ordered in Driver Side Only, or Both Seats. The Escalade front-end conversion kit comes complete with steel hood and fenders, grille and grille brackets, bumper assembly, headlights and turn signals, and even new tow. ![]() The GMT900 brackets are 6.5″ in the front and 5″ in the rear for a 6 degree layback angle (same as factory). Layback angle is approximately 7 degrees and the GMT800 front is 6″ off the floor and rear is 4″ off the floor (factory seat height). These will work with the Corbeau or Braum slider rails as well. There are multiple seat mounting positions to position the seat up to 3″ forward and back and 1.5″ left or right (expect on GMT400 brackets). They will accommodate a center console and drop directly on to the factory floor bolt pattern, no trimming or drilling is required. The passenger side weighs approximately 12.75 pounds and the driver side weighs approximately 13.0 pounds for the GMT800 and GMT900 brackets, and slightly less for the GMT400 brackets. AC ducting that goes from the center console along the floor to the jump seat. That includes: 1: New front center dash storage area/trim were your new USBs and power outlet come from. They can be easily powder coated at your leisure (I do not offer powder coating service on these). At this point, it was a matter of making sure I had everything I needed to install. Brackets will ship raw ready for your paint or powdercoat. KUBOTA DLC IS REQUIRED FOR PASSENGER TO FUNCTION. It has a handful of config options but enjoy the truck y’all. Harness mounting holes are 1/2″ in diameter. It’s a nice little truck with the typical passenger and IC and stuff like that. There are holes to mount a 3, 4, 5, or 6 point harness directly to the brackets without the need for a roll cage (this is NOT a replacement for a roll cage!). 9 2020 2021 Chevrolet Silverado 1500 center console jump seat with storage (Fits: Chevrolet Silverado 1500) 399. ![]() These are laser cut from 3/16″ steel and are fully MIG welded with support gussets for strength. They are intended for Corbeau, Sparco, or Braum seats but can work with other seats as well (Kirkeys, etc.). These seat brackets are made to install aftermarket seats on the factory floor bolts in 1988-2018 GMT400, GMT800, GMT900, and GM2kxx GM Trucks (Silverado, Sierra, Tahoe, Suburban, Denali, Escalade, Yukon, etc.). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |